SEASAM DRONE - Update the drone

If you cannot synchronize your drone & remote, and SEASAM flashes its green and blue LEDs alternatively, it means that SEASAM’s remote needs to be activated and updated.

To update your remote, please follow the following steps:

• Make sure that the drone and the remote are turned off.
• Put the fully charged battery in the drone.
• Turn on the SEASAM remote.
• Place the remote in the dock at the top of the drone. Do not remove the remote until the update process is complete.
• SEASAM turns on and begins the update process. It may take up to 10 minutes.
• Once the update process is complete, the drone and the remote synchronize. The remote displays the “Disarmed” Scenario.

You may now proceed with the first time setup, and your drone will be ready to dive!

During the update process of SEASAM, the firmware may get stuck because of a temporary connection loss. If this happens, the progress bar stops moving and the update gets stuck.
If this happens, turn off your remote, then put it on SEASAM to shut it down. The app will display an error message. Turn the remote back on, then turn SEASAM back on and resume the update process via the app.

In order to update SEASAM, use the official SEASAM App available on the computer you bought with the drone. Check for the update on Settings > Drone Update and select “Automatic Check for Updates”. The update’s download will start automatically.
If you are not able to update the drone, please contact our technical support by email support@notiloplus.com.
Please keep in mind that unless a critical update is needed, you will be able to dive with SEASAM without updating it.

If you found a bug on SEASAM Control, please let us know by contacting our technical support by email support@notiloplus.com – this will be greatly appreciated!

If SEASAM Control doesn’t detect your SEASAM, you can bring the computer closer to the drone.
If the problem remains please contact our technical support by email support@notiloplus.com

For the first starting up, SEASAM will need to be updated and registered.

To do so, please follow these steps:

1. Charge all the equipment to the fullest: the battery, the remote, the control unit, the WiFi Reel and the controller
2. Open the SEASAM Control App on the control unit delivered with the drone.
3. Put the 100% charged battery in the dedicated compartment under the drone (a sound signal will inform you the battery is correctly positioned) then close it properly until touch.
4. Connect the WiFi Reel to the drone using the cable and secure it with the carabiner.
5. Switch on the WiFi Reel, the blue LED is flashing quickly.
6. Switch on the remote by pressing few seconds the “Select” button at the top of the remote and put it on the dedicated support on the drone. Don’t remove it until the end of the setting process. The drone will switch on and test all its components (lights activation, propellers, sound signal). The WiFi Reel and the drone are connected, the blue LED is flashing slowly.
7. Connect the control unit to the drone’s WiFi “seasam-0044BXXXXXX”.  If you cannot detect the WiFi signal bring the control unit closer to the drone.
8. Start the SEASAM Control App on the control unit, the password to connect to the WiFi Reel’s WiFi will be displayed. You can find the password in Settings > WiFi Reel Settings.
9. Copy the password and connect to the WiFi Reel’s WiFi “seasam-beacon-XXXXXXXXXXXX” and paste the password. The password should be entered only once, the unit control will then connect automatically to the WiFi Reel.
10.  Connect the control unit to internet and, in the SESAM Control App, go to Settings > Drone Update and select “Automatic Check for Updates”. The update’s download will start automatically.
11. Once the update uploaded, reconnect your control unit to the WiFi Reel’s WiFi and select “Update drone” on the SEASAM Control App. The drone will receive the update and restart testing all its components (lights activation, propellers, sound signal). At the end of the process, the drone indicates « Disarmed Ready » on the remote and its green LED is constant.
12. Go to the “Home” tab, your drone is ready.

To calibrate the drone, put it on a flat surface, connect it to SEASAM Control then select Settings > Drone Calibration and launch the calibration process.

To calibrate the controller connect it to SEASAM Control then select Settings > Controller Settings. Select  “Calibrate Gamepad” and follow the process as indicated on the App.