The Navigator is waterproof but you have to be very careful with the connectors which are not. Remember to dry them well before connecting them or plugging them back into their caps.
The Navigator is waterproof but you have to be very careful with the connectors which are not. Remember to dry them well before connecting them or plugging them back into their caps.
The two antennas, present on the Navigator and on the Ground Station are fragile and need to be handled with care. To screw the antennas on, the metal ring on the Navigator as well as on the Ground Station must be held.
As soon as the drone is turned off, for example in a situation of battery change, it is mandatory to turn off and turn on the Navigator too. This allows you to synchronize them together correctly.
Yes, it is possible to use the Navigator in supervised mode, but you must be careful about the depth of the diver, depending on the length of the cable.
When descending to depth, if you do not respect the length of the cable, then the Navigator can be towed by the drone and can be totally submerged. This can damage connectors that are not waterproof.
Press and hold the ON/OFF button on the front panel. The blue and orange LEDs will turn off. Your Ground Station is now turned off.
Press the black button on the front panel, the first two blue LEDs of the antenna will light up. The orange LEDs indicate the charge level.
The Ground Station is operational after 2 or 3 minutes when the blue LEDs of the antenna are light up.
The length of the cable is customized according to the customer’s needs
No, the Ground Station is not waterproof. It must remain close to the operator in a dry place.
The signal range between the two antennas is about 100m. It is recommended not to send the Navigator and the drone beyond 100m from the Ground Station.
No, We advise you not to touch the elements when not specified by Notilo Plus. If you have any doubts, do not hesitate to contact the support department by e-mail at support@notiloplus.com
It depends on the use: if ROV mode, you don’t need the WiFi Reel, if other uses such as automatic localisation for boat inspection, you will need the WiFi Reel in this case.
You can also refer to the user manual.
The Navigator is towed by the drone.
Open the Seasam Control application. A page concerning the configuration mode opens, scroll down this page and select the tab allowing you to connect to the Internet. Then click on “Continue”.
The settings tab opens. Open the menu and select “Interface”. You can now check the “Map” box and save the changes.
You can return to the home screen. The map now appears as a miniature in the corner of your screen. Click on it to make it your main screen.
By zooming out as much as possible, you can virtually go to the place where you want to make your dive.
Finally, go back to your settings and select “Choose New Configuration”, then you can select “Cartography”. You are now able to calibrate propely your equipment.
No, it is not possible to use the Ground Station while it is charging. You will have to wait until the end of its charging to use it.
The charging time for the Ground Station is 3 hours for 3.5 hours of autonomy. The Ground Station is charged with a dedicated charger.
The charging time of the Navigator is 2 hours for 6 hours of autonomy. Please keep in mind that this may vary depending on your use of the equipment.
To charge the Navigator, you will find a suitable charger.
When the Navigator is fully charged, all LEDs will go out.
Press the ON/OFF button. The Navigator’s two green center LEDs will light up.
The Navigator is operational as soon as the outer left LED is stable.
Press the ON/OFF button. After a few seconds, the battery LED will turn off and the other LEDs will turn off out after a few seconds.
Place the battery in your drone. Unscrew your battery compartment and place the battery in the dedicated slot. You should hear a beep indicating that the battery is properly positioned. Unscrew the battery compartment completely until there is no more space.
Connect the cable between the drone and the Navigator. For the Navigator, the connection is located in the lower part, the central location among the 3. A drone icon on a sticker will allow you to better visualize this connection. Check that the connectors are correctly plugged in by gently pulling on the connector.
Do not forget to screw the two caps together.
Finally, secure the cable to the drone and Navigator with the two carabiners.